French Fries Cutting Machine 1000 kg/h

Potato strip cutter that pushes whole tubers through a fixed blade grid to produce uniform French fry strips, with a water or hydraulic feed and interchangeable grid sets for different cross-sections.

SKU: VL-062 Category: Tag:

French Fries Cutting Machine 1000 kg/h

French fries cutting machine pushing potatoes through a blade grid into strips

Strip cutter that drives whole potatoes through a fixed blade grid, producing fries of a set cross-section at line rate, with the grid swapped to change the cut.

How it works

Whole tubers are fed — by hand, by a belt or hydraulically — into a feed chamber behind a blade grid. A pusher advances the tuber through the grid; the grid is a set of knives held in a frame that slices the tuber into strips as it passes. Strip length is whatever is left of the tuber, so a long tuber produces long strips and a short one produces short strips. Cut strips drop into water or onto a belt and go on to washing, blanching and frying.

Water feed is common: the tuber is carried through the grid by a water jet, which reduces the force required and washes starch off the cut surface. Hydraulic feed with a pusher gives more positive control on hard or cold tubers.

Suitable for

French fry lines from small catering units up to continuous industrial plants; potato wedges and steak fries with a different grid; other firm root vegetables cut into strips — carrot, parsnip, sweet potato; plants where fry length consistency drives the pack specification.

Not suitable for

Soft or sprouted tubers that deform instead of cutting cleanly; product that must be cut to an exact length rather than a cross-section; very small tubers that pass through the grid without being cut; anyone expecting the machine to sort out length — that is a separate grading step and often a bigger yield factor than the cut itself.

Material & compliance

Blade grid, feed chamber, pusher and frame in SUS304 (EN 1.4301); blades in hardened stainless with replaceable sets. Feed opening guarded and interlocked; grids changed with the drive isolated; contact parts removable for washdown.

Supplied with CE declaration of conformity and DoC on request; material certificate EN 10204 3.1 available for contact parts.

Selection notes

Start from the cross-section you sell and the length distribution you can tolerate. The grid sets the cross-section; length comes from the tuber, so your raw material specification and your destoning and grading upstream matter as much as the cutter. Ask how the grid is changed and how long it takes, because a slow changeover costs you every time you switch product. Check blade material and how many cuts a set holds before it starts producing feathered edges.

When you should not buy this machine: If your tubers are inconsistent in size and you have no upstream sizing, the cutter will produce a wide length spread and you will blame the machine for a raw material problem. Also skip it if you need exact-length fries: a grid cutter cuts cross-section only, and length control means sizing the tuber first.

Key specifications

Parameter Value
Capacity 300-3000 kg/h by feed type (TYPICAL, confirm with factory)
Strip cross-section 6×6 to 12×12 mm by grid (TYPICAL)
Tuber diameter 40-100 mm by feed (TYPICAL)
Grid sets Interchangeable, 2-5 supplied (TYPICAL)
Motor power 1.5-4.0 kW (TYPICAL)
Contact material SUS304 (EN 1.4301)
Power supply 380V/3P/50Hz or 415V/3P/50Hz, customizable

Specification values are industry-typical ranges for this machine class and are not verified against a specific factory datasheet. Replace them with measured factory data before publication.

FAQ

Why do my fries come out different lengths?

Because the grid cuts cross-section, not length. Strip length follows tuber length, so consistent fries come from consistent tubers — size the raw material before it reaches the cutter.

How often do the blades need changing?

Depends on tonnage and on what is in the water. Feathered or torn edges and rising starch damage are the signs, not a calendar interval.

Can I cut wedges on the same machine?

Usually yes, with a different grid. Confirm the grid is available and that the feed chamber accepts the cut, because wedge grids load the knife differently from square ones.

Related equipment

This unit is one stage of a complete processing line. For the full range of cutting and slicing equipment, or to compare this model against the Vegetable Slicing Machine 1200 kg/h, see the complete equipment catalogue. Capacity, material grade and utility requirements can be confirmed through a quote request.

material

SUS304 (EN 1.4301)

power

380V/3P/50Hz, Customizable

certification

CE+DoC (EU 2023/1230 ready)

surface_finish

Ra≤0.8 μm (food-grade)

application

Potato, Root Vegetables

capacity

0.5–1 t/h

automation

Semi-Automatic, Fully Automatic

cut_type

Strip

Reviews

There are no reviews yet.

Be the first to review “French Fries Cutting Machine 1000 kg/h”

Your email address will not be published. Required fields are marked *