Crinkle Cutting Machine 1500 kg/h

Cutting unit that slices vegetables and fruit into wavy or corrugated pieces with a set of offset circular or reciprocating blades, giving a cut face that holds seasoning and stands up in frying and dehydration.

SKU: VL-102 Category: Tag:

Crinkle Cutting Machine 1500 kg/h

Crinkle cutting machine slicing vegetables into wavy corrugated pieces

Cutting unit that makes the wavy cut. A straight slice is the default; a crinkle slice is a decision — the wavy face holds more surface for seasoning, keeps its shape better in frying, and reads as a premium product on the shelf. The machine is essentially a slicing unit with a blade geometry that cuts on two axes at once, and the specification is entirely about how true that geometry stays.

How it works

Product is fed through a feed tube or singulating pocket into the blade station. Where a straight slicer carries the product past a single spinning blade, a crinkle cutter uses either offset circular blades that turn at slightly different speeds, or a reciprocating blade frame that moves against a fixed comb. Either way the product meets the cutting edge along two axes at once, and the slice comes out with a corrugated face instead of a flat one.

The two settings are slice thickness and feed speed, and the wave pattern comes from the blade geometry rather than from an operator control. That matters for maintenance: on this machine class, the wave is a hardware property. Blade alignment and sharpening are the whole specification, because a blade that is sharp but misaligned cuts a wave that is deep on one side and flat on the other, and nobody notices until the finished product shows it.

Suitable for

Snack and fried-product lines where the corrugated face holds seasoning and oil drainage; fresh-cut vegetable lines selling a differentiated cut; dehydrated vegetable and fruit products where the wavy face dries and rehydrates faster; salad and garnish operations where a wavy cut adds visual value; processors running both straight and crinkle cuts from one machine with a blade changeover.

Not suitable for

Product that must meet a strict straight-cut specification, where a wave is a defect; very soft or very hard product outside the machine’s tooled range, because the blade geometry is set for a firmness window; operations without blade maintenance discipline, since a worn or misaligned blade set degrades quietly; anyone wanting thickness to change mid-run by a dial — on this machine class the wave is mechanical and the thickness range is set by the blade assembly.

Material & compliance

Frame, feed guides and discharge chutes in SUS304 (EN 1.4301); blades in stainless blade steel, supplied as matched sets and treated as consumables. Blade stations fully guarded with interlocked access for changeover. The machine opens for wash-down, because cut vegetable tissue and starch accumulate in the feed area and dry hard. Blade assemblies handled under a defined change procedure to keep the offset geometry true.

Supplied with CE declaration of conformity and DoC on request; material certificate EN 10204 3.1 available for contact parts.

Selection notes

Ask to see cut samples from a blade set with stated hours on it, not from a fresh set — the gap between a new blade and a half-worn one is where this machine class shows its quality. Ask how the offset geometry is maintained through sharpening: whether blades are sharpened in place, returned to the supplier, or replaced as a set. Check the thickness range against your products and how it is changed. Check the feed arrangement against your upstream equipment, because singulation quality decides slice uniformity more than the blades do.

When you should not buy this machine: If your specification is a straight slice, buy a straight slicer — a crinkle machine is a more expensive way to make a cut you do not want. And if nobody on your site will own blade alignment as a routine, the wave will drift and the product will drift with it.

Key specifications

Parameter Value
Capacity 1000-3000 kg/h by feed and product (TYPICAL, confirm with factory)
Cut type Wavy or corrugated slice, thickness set by gap
Blade arrangement Offset circular blades or reciprocating frame
Thickness 1.5-6 mm by product (TYPICAL)
Wave amplitude Set by blade offset geometry
Feed Manual feed tube or automatic singulation
Blade type Stainless blade steel, replaceable set
Contact material SUS304 (EN 1.4301)

Specification values are industry-typical ranges for this machine class and are not verified against a specific factory datasheet. Replace them with measured factory data before publication.

FAQ

Is the wave pattern adjustable?

Not continuously. The wave comes from the blade geometry — the offset between cutting edges — and it changes when the blade assembly changes. Thickness is adjustable; wave depth is a property of the tooling you bought.

Why is my wave deeper on one side?

Blade alignment or uneven wear. The two axes have to cut in a fixed relationship, and once that relationship drifts the slice shows it. This is a maintenance finding, not an operating one: check the blade set against the supplier’s alignment specification.

Can it handle tomatoes?

With care and usually a slower feed, but tomatoes sit at the soft edge of this machine class. The blade geometry that makes a good wave on a carrot will crush a ripe tomato — test with your product before committing.

Related equipment

This unit is one stage of a complete processing line. For the full range of cutting and slicing equipment, or to compare this model against the Vegetable Dicing Machine 1500 kg/h, see the complete equipment catalogue. Capacity, material grade and utility requirements can be confirmed through a quote request.

material

SUS304 (EN 1.4301)

power

380V/3P/50Hz, Customizable

certification

CE+DoC (EU 2023/1230 ready)

surface_finish

Ra≤0.8 μm (food-grade)

application

Potato, Carrot, Cucumber

capacity

1–3 t/h

automation

Semi-Automatic, Fully Automatic

cut_type

Crinkle Slice, Wave Slice

Reviews

There are no reviews yet.

Be the first to review “Crinkle Cutting Machine 1500 kg/h”

Your email address will not be published. Required fields are marked *