Plate Juice Pasteurizer 2 t/h

Plate juice pasteurizer that holds clear and cloudy juices at pasteurizing temperature in seconds of contact — plate heat exchange with regeneration, flash cooling, and the gentle thermal profile that keeps fresh flavour in a shelf-stable product.

SKU: VL-176 Category: Tag:

Plate Juice Pasteurizer 2 t/h

Plate juice pasteurizer with stainless plate pack holding juice at pasteurizing temperature

Juice spoils by the hour, and heat fixes it — the question is how much flavour the fix costs. Long holds in batch kettles cook the freshness out of the product; a plate pasteurizer takes the opposite trade: a thin film of juice flows through corrugated stainless plates against hot water, reaches pasteurizing temperature in seconds, holds it through a short tube run, and flash-cools against incoming cold juice before the aroma has time to boil off. It is the standard machine between the press and the filler for exactly this reason — fast enough to keep the flavour, hot enough to hold the shelf life.

How it works

Juice feeds a plate pack where three circuits share the same frames: regeneration plates warm incoming cold juice against outgoing hot product, recovering most of the heat; heating plates bring the juice to setpoint against hot water from a separate loop; and a holding tube guarantees every particle the legal hold time at temperature before the flow reverses through cooling plates. Controls run the classic interlocks — forward flow only when holding temperature is proven, automatic divert of under-temperature product back to feed, and CIP capability through the same pack. Cloudy juices run lower shear and gentler differential; pulpy products may need a free-flow plate channel or a wide-gap plate, which is a selection question, not an afterthought.

Suitable for

Juice bottlers pasteurizing clear apple, grape and berry juices ahead of hot-fill or aseptic filling; cloudy and pulpy juice lines running wide-gap plates tuned for fibre; dairies-adjacent juice rooms sharing hot-water utility; juice plants adding shelf life to fresh product without cooked flavour; any pressed-juice stream where batch-kettle taste loss or short shelf life is the current complaint.

Not suitable for

Products with particles or whole pulp that bridge plate channels — those need tubular or scraped-surface sterilizers; UHT-class aseptic products needing sterile filling downstream, which is a different pressure and sterility class; tiny juice rooms under a couple hundred litres an hour, where a batch pasteurizer vat is cheaper and adequate; and plants whose real problem is upstream contamination — pasteurizing dirty juice buys shelf life, not quality.

Material & compliance

Plate packs in food-grade stainless with food-safe gaskets rated for the temperatures; hot-water loop separated from product circuit; holding tube sized and documented for the pasteurizing regime; controls with divert-valve logic, temperature recording and CIP integration, because pasteurization records are the core of any juice audit.

Supplied with CE declaration of conformity and DoC on request; material certificate EN 10204 3.1 available for contact parts; plate gasket food-contact declarations per supplier.

Selection notes

Size on your worst product, not your best: cloudy, pulpy juice at cold feed temperature is the case that sets plate area and pump spec. Ask about regeneration rate — 85-95% heat recovery is the difference between a sane energy bill and a painful one. Confirm the divert logic and how under-temperature product is handled, in writing, because that interlock is the machine’s licence to operate. Check gasket life and spare-plate economics for your CIP chemistry; gaskets are the running cost. And match outlet temperature to your filler — hot-fill wants the product hot, aseptic wants it cold, and the machine must be piped and controlled for the one you actually run.

When you should not buy this machine: If your product has fibre and chunks, buy the tubular or scraped-surface machine first — plugging a plate pack daily is not a maintenance plan. And if your volumes are small and your market is farm-gate chilled juice, a pasteurizing vat and honest refrigeration undercut this machine on every number that matters.

Key specifications

Parameter Value
Capacity 1000-5000 L/h by product and regime (TYPICAL, confirm with factory)
Process HTST, 85-95 °C with 15-30 s hold (TYPICAL)
Regeneration 85-95% heat recovery (TYPICAL)
Plate pack Food-grade stainless, wide-gap option for pulp
Controls Divert logic, recording, CIP-integrated
Contact material SUS304 / SUS316L plates, food-safe gaskets
Power supply 380V/3P/50Hz, 3-10 kW class plus hot-water loop

Specification values are industry-typical ranges for this machine class and are not verified against a specific factory datasheet. Replace them with measured factory data before publication.

FAQ

Plate or tubular pasteurizer for juice?

Clear and light cloudy juices are plate territory — better heat recovery and lower cost. Fibrous, pulpy or particulate products belong in tubulars that cannot plug. Decide by your most difficult product, and let the easy ones follow.

How much flavour does it cost compared to batch heating?

Seconds of exposure against minutes: a plate pasteurizer’s flavour difference is usually the reason lines convert. Blind shelf comparisons on your own juice are the honest test — run a pilot or a factory trial before committing the whole line.

What does daily operation actually involve?

Start-up to temperature, flow run with recording, CIP at end of shift, and periodic gasket checks. Most of the routine is controls work, which is why the divert interlock and logging quality deserve as much attention in the purchase as the plate area.

Related equipment

This unit is one stage of a complete processing line. For the full range of pulping and juicing equipment, or to compare this model against the Tubular Juice Sterilizer 3000 L/h, see the complete equipment catalogue. Capacity, material grade and utility requirements can be confirmed through a quote request.

material

SUS304 (EN 1.4301)

power

380V/3P/50Hz, Customizable

certification

CE+DoC (EU 2023/1230 ready)

surface_finish

Ra≤0.8 μm (food-grade)

application

Clear Juice, Cloudy Juice, Nectar Base

capacity

1000-5000 L/h

automation

Fully Automatic

process

HTST 85-95 °C

Reviews

There are no reviews yet.

Be the first to review “Plate Juice Pasteurizer 2 t/h”

Your email address will not be published. Required fields are marked *