Vacuum Cooling Machine 1000 kg/cycle

Pre-cooling unit that pulls product down in temperature by evaporating its own surface moisture under vacuum, removing field heat from leafy greens and mushrooms in minutes rather than hours.

SKU: VL-075 Category: Tag:

Vacuum Cooling Machine 1000 kg/cycle

Vacuum cooling machine removing field heat from leafy greens under vacuum

Pre-cooling unit that removes field heat quickly by letting the product cool itself. Under vacuum, water boils at a low temperature, and the latent heat needed to evaporate it comes out of the product. For leafy greens, this is the difference between a shelf life measured in days and one measured in a day.

How it works

Loaded trolleys or pallets go into a sealed chamber. A vacuum pump system evacuates the chamber; as pressure falls, the boiling point of water drops below the product temperature and surface moisture begins to evaporate. The evaporation removes heat from the product, which cools until it reaches the temperature at which its own water stops boiling at the current pressure. When the target temperature is reached, the vacuum is released and the chamber is opened.

Cooling is uniform through the load rather than from the outside in, which is why vacuum cooling works where forced air struggles. The cost is water: the product loses weight, typically 2-4 %, because the moisture it loses is its own. Some machines offer a water spray before the cycle to reduce that loss.

Suitable for

Leafy greens and salad crops where field heat drives respiration and shelf life; mushrooms, which cool poorly in air; cut flowers and herbs; product with a high surface-area-to-mass ratio, where evaporation reaches the whole piece; plants that need to turn harvest around within hours rather than overnight.

Not suitable for

Dense, low-surface-area product such as whole root vegetables, where the moisture is inside and the surface dries before the core cools; product sold by weight where the moisture loss is a direct cost; sealed or wrapped product, which cannot evaporate; crops with a thick cuticle or wax layer; anyone without the vacuum capacity — the pump set is the machine, and undersizing it just makes a slow machine.

Material & compliance

Chamber, door seals and trolley guides in SUS304 (EN 1.4301); the chamber is a pressure vessel in reverse and must be built and certified as one, with a door interlock that cannot be defeated. Condensate handling matters: the water that leaves the product has to be captured and drained hygienically.

Supplied with CE declaration of conformity and DoC on request; material certificate EN 10204 3.1 available for contact parts. Pressure vessel documentation supplied with the chamber.

Selection notes

Ask for the cycle time to target temperature on your product and load, not the chamber volume — the pump capacity decides the cycle, and a big chamber with a small pump is a slow machine. Ask about the weight-loss figure and whether pre-wetting is offered. Check the door seal and interlock design, because it is cycled every run and it is the part that fails.

When you should not buy this machine: If your product is dense root vegetables, or if you sell strictly on weight, vacuum cooling costs you moisture for speed you do not need — a forced-air chiller or a hydro-cooler is the better fit. Also skip it if your harvest window is long enough to cool in a cold room overnight.

Key specifications

Parameter Value
Cycle capacity 500-1500 kg per cycle (TYPICAL, confirm with factory)
Pull-down time 15-30 min per cycle (TYPICAL)
Target temperature 1-4 °C core (TYPICAL)
Weight loss 2-4 % by product (TYPICAL)
Vacuum level Down to about 6-7 mbar absolute (TYPICAL)
Contact material SUS304 (EN 1.4301)
Power supply 380V/3P/50Hz or 415V/3P/50Hz, customizable

Specification values are industry-typical ranges for this machine class and are not verified against a specific factory datasheet. Replace them with measured factory data before publication.

FAQ

How much weight does the product actually lose?

Typically 2-4 %, and it is water the product had. For salad sold by weight that is a margin question; for salad sold by shelf life it is usually the right trade. Pre-wetting before the cycle reduces the loss on some crops.

Why does it not work on carrots?

Because the moisture cannot get out fast enough. Vacuum cooling relies on surface evaporation to carry heat away; a dense root vegetable dries on the outside while the core stays warm. Air or water cooling reaches it better.

Is the chamber a pressure vessel?

It works under external pressure rather than internal, but it is designed and certified as a pressure vessel. Ask for that documentation with the machine; a chamber without it is not a machine you want on a food site.

Related equipment

This unit is one stage of a complete processing line. For the full range of cooking and blanching equipment, or to compare this model against the Hydro Cooling Machine 3000 kg/h, see the complete equipment catalogue. Capacity, material grade and utility requirements can be confirmed through a quote request.

material

SUS304 (EN 1.4301)

power

380V/3P/50Hz, Customizable

certification

CE+DoC (EU 2023/1230 ready)

surface_finish

Ra≤0.8 μm (food-grade)

application

Leafy Greens, Mushroom, General Produce

capacity

0.5–1.5 t/cycle

automation

Fully Automatic

cooling_method

Vacuum Evaporation

Reviews

There are no reviews yet.

Be the first to review “Vacuum Cooling Machine 1000 kg/cycle”

Your email address will not be published. Required fields are marked *