Continuous Roasting Machine 500 kg/h

Thermal treatment unit that roasts nuts, seeds and vegetables on a rotating drum or multi-zone belt with controlled hot air, developing colour and flavour without oil contact before cooling and further processing.

SKU: VL-084 Category: Tag:

Continuous Roasting Machine 500 kg/h

Continuous roasting machine turning nuts and seeds through controlled hot-air zones

Thermal treatment unit that develops colour, flavour and texture without adding oil. Roasting sits between drying and frying as a process: the temperatures are frying-class, the mass transfer is drying-class, and the product that leaves is changed in ways a buyer tastes immediately.

How it works

Product is carried through a heated chamber on a perforated belt or through a rotating drum. Hot air, generated electrically, by gas burner or by a steam exchanger, is circulated through the product bed in temperature zones along the length: early zones drive off surface moisture, later zones develop colour and roast flavour. Belt speed sets residence time; zone temperatures set the roast profile.

The control that matters is the product temperature, not the air temperature. A roast specified as “medium” is a product temperature and a holding time, and the same air setting gives a different product when the bed depth or the inlet moisture changes. Machines with product-temperature feedback hold a roast specification through a shift; machines with only air control need an operator watching colour.

Suitable for

Nut and seed roasting where oil roasting is unwanted for cost, diet or allergen reasons; vegetable slices and cubes for snack and ingredient applications; pre-roasting ahead of grinding for pastes and spreads; lines needing a repeatable roast profile documented for a buyer specification; plants with gas, electric or steam utilities — the heat source is chosen at design, not fixed by the machine.

Not suitable for

Product needing oil-roast flavour and appearance, which dry roasting does not replicate; very high-moisture product, where a drying stage must precede the roast or the roast becomes a slow, expensive dryer; small batches with frequent product changeover, where a batch roaster is more flexible; anyone unable to manage the fire risk of a hot, oily dust-laden chamber — roasting equipment needs a cleaning discipline, not just a cleaning procedure.

Material & compliance

Chamber, drum and contact parts in SUS304 (EN 1.4301); belt in food-grade mesh rated to roast temperature. Burner or electrical sections enclosed with over-temperature protection; residue trays accessible because roast residue on hot surfaces is the fire case.

Supplied with CE declaration of conformity and DoC on request; material certificate EN 10204 3.1 available for contact parts.

Selection notes

Ask whether the machine controls product temperature or air temperature, and how the roast profile is recorded — that answer separates a process machine from a heated box. Check zone count against your product range: two zones roast one product; four zones hold a specification across several. Check the cleaning route for oil residue and dust, and what the fire-suppression provision is. Check the heat source against your utilities and their cost.

When you should not buy this machine: If your volumes are small and your products rotate, buy a batch oven — a continuous roaster only earns its cost running long single-product campaigns. And if your product needs oil-roast character, no dry roaster will get there, and adding oil afterwards is not the same thing.

Key specifications

Parameter Value
Capacity 200-800 kg/h by belt width and product (TYPICAL, confirm with factory)
Roasting temperature 120-180 °C by product (TYPICAL)
Residence time 10-40 min by product (TYPICAL)
Heating source Electric, gas or steam exchanger by site
Zones Multi-zone temperature control along the roast
Contact material SUS304 (EN 1.4301)
Power supply 380V/3P/50Hz or 415V/3P/50Hz, customizable

Specification values are industry-typical ranges for this machine class and are not verified against a specific factory datasheet. Replace them with measured factory data before publication.

FAQ

Is dry roasting healthier than oil roasting?

It adds no oil, which matters for fat content and for allergen management on shared lines. “Healthier” depends on the product and the buyer’s claim; the equipment-level fact is that no oil enters the process.

Why does the roast vary between shifts?

Because air temperature is not product temperature. Bed depth, inlet moisture and ambient all shift the product temperature under the same air setting. Product-temperature feedback, or a disciplined bed-depth procedure, closes the gap.

Can it cool as well as roast?

Some machines add a cooling zone at the discharge, and it is worth specifying: roast product carries heat into storage and keeps cooking. Without a cooling zone, plan a separate ambient or forced-air cooler immediately downstream.

Related equipment

This unit is one stage of a complete processing line. For the full range of cooking and blanching equipment, or to compare this model against the Continuous Frying Machine 500 kg/h, see the complete equipment catalogue. Capacity, material grade and utility requirements can be confirmed through a quote request.

material

SUS304 (EN 1.4301)

power

380V/3P/50Hz, Customizable

certification

CE+DoC (EU 2023/1230 ready)

surface_finish

Ra≤0.8 μm (food-grade)

application

Nuts, Seeds, Vegetable Slices

capacity

200–800 kg/h

automation

Fully Automatic

heating_source

Electric, Gas, Steam

Reviews

There are no reviews yet.

Be the first to review “Continuous Roasting Machine 500 kg/h”

Your email address will not be published. Required fields are marked *