Hydro Cooling Machine 3000 kg/h

Flume or immersion cooler that drops product temperature quickly in chilled water, stopping the cooking process after blanching and reducing field heat after harvest.

SKU: VL-045 Category: Tag:

Hydro Cooling Machine

Hydro cooling machine lowering product temperature in chilled water

Hydro cooler that removes heat from product by direct contact with chilled water — the standard way to stop a blanching process or to pull field heat out of harvested produce.

How it works

Product enters a tank or flume of chilled water and is carried through it by a belt, by water flow, or by both. Heat moves from the product surface into the water; the water is continuously recirculated through a chilling source — an ice bank, a chiller or a glycol heat exchanger — and back to the tank. Product leaves at a temperature set by water temperature, residence time and piece size, and is then drained before the next stage.

Cooling rate is governed by surface area to volume. Small pieces cool in a couple of minutes; a whole large root vegetable may need a much longer pass, and the residence time must be set for the largest piece, not the average.

Suitable for

Cooling immediately after blanching, which is where it earns its place — blanching does not stop until the product is cold; removing field heat from leafy greens, beans and sweetcorn after harvest; cooling before freezing, so the freezer does the freezing rather than the sensible cooling; cooling packed product after a hot-fill or pasteurising tunnel.

Not suitable for

Product that must stay dry, where a forced-air or vacuum cooler is correct; product that absorbs water or is damaged by immersion, such as some berries and delicate leaf in a deep flume; product where water uptake changes the declared weight; situations without clean, treated, chilled water available at volume.

Material & compliance

Tank, flume, belt and pipework in SUS304 (EN 1.4301); water circuit designed for filtration, sanitiser dosing and full drainage. Chilled water is a food-contact medium and is treated as such: it is filtered and dosed, monitored, and changed on a schedule.

Supplied with CE declaration of conformity and DoC on request; material certificate EN 10204 3.1 available for contact parts.

Selection notes

Size on the heat load, not on kg/h alone — inlet temperature, target temperature and piece size decide the required residence time and the chilling capacity. Ask what happens to the water: it is the most likely source of cross-contamination in a line, and filtration plus sanitiser control is not optional. Check how the product is drained after the tank, since carrying water into a freezer or a pack is a downstream problem.

When you should not buy this machine: If your product cannot tolerate immersion, use forced-air or vacuum cooling — hydro cooling is cheap and fast precisely because water carries heat so well, and that comes with wet product. Also skip it if you cannot treat and chill the water continuously: warm, untreated recirculated water turns a cooler into a contamination spreader.

Key specifications

Parameter Value
Capacity 500-10000 kg/h by tank size (TYPICAL, confirm with factory)
Water temperature 0-5 °C chilled water (TYPICAL)
Cooling time 2-10 min by product and size (TYPICAL)
Water treatment Filtration and sanitiser dosing (TYPICAL)
Chilling source Ice bank, chiller or glycol (TYPICAL)
Contact material SUS304 (EN 1.4301)
Power supply 380V/3P/50Hz or 415V/3P/50Hz, customizable

Specification values are industry-typical ranges for this machine class and are not verified against a specific factory datasheet. Replace them with measured factory data before publication.

FAQ

Why cool immediately after blanching?

Because blanching does not stop when the product leaves the blancher — residual heat keeps cooking it and takes it past the point you set. Fast cooling to below the enzyme-inactivation range is part of the blanching process, not an optional extra.

How cold should the water be?

Typically near freezing, held there by an ice bank or chiller. Warmer water still cools, but slower, and the whole point is to get through the critical temperature range quickly.

Is the water a contamination risk?

Yes, if it is not managed. Recirculated water contacting product must be filtered, dosed with sanitiser and monitored, because it touches every piece that passes through the line.

Related equipment

This unit is one stage of a complete processing line. For the full range of cooking and blanching equipment, or to compare this model against the Continuous Belt Blancher 2500 kg/h, see the complete equipment catalogue. Capacity, material grade and utility requirements can be confirmed through a quote request.

material

SUS304 (EN 1.4301)

power

380V/3P/50Hz, Customizable

certification

CE+DoC (EU 2023/1230 ready)

surface_finish

Ra≤0.8 μm (food-grade)

application

Leafy Greens, Root Vegetables, General Produce

capacity

2–5 t/h

automation

Fully Automatic

heating_source

Chilled Water

Reviews

There are no reviews yet.

Be the first to review “Hydro Cooling Machine 3000 kg/h”

Your email address will not be published. Required fields are marked *