Flash Dryer 500 kg/h

Pneumatic flash dryer that suspends wet granular feed in a rising hot-air duct and dries it in seconds, the standard machine for starch-root powders, ginger pomace, protein flours and milled vegetable intermediates that must not stew in a bed dryer.

SKU: VL-146 Category: Tag:

Flash Dryer 500 kg/h

Flash dryer suspending wet starch granules in a rising hot-air duct for drying within seconds before cyclone collection

Some products dry best lying still on a belt; others would stew, cake or sour before a bed dryer finished them. Wet starch, ginger pomace, milled peels and protein flours dry in seconds when each particle flies free in hot air — and that is the entire principle of the flash dryer: suspend the particle in the airstream, let heat and mass transfer do in metres of duct what takes hours on a tray, and catch the dry powder at the other end.

How it works

Wet feed — dewatered cake, filter-cake pomace, centrifuged starch — is metered by a screw or rotary feeder into the base of a vertical drying duct, where a hot-air stream at typically 130-180 °C entrains the particles instantly. Moisture flashes off the huge combined surface as the suspension accelerates up the duct; residence time is seconds, and the evaporative cooling keeps particle temperature near wet-bulb, which protects starches and proteins from heat damage. At the duct top, cyclones separate dry powder from humid air; a classifier or sifter can return oversize for a second pass. Air heating runs on steam, gas or electric exchangers; the controls link feed rate to exhaust temperature so exit moisture holds constant despite feed swings.

Suitable for

Starch plants drying potato, cassava and wheat starch from dewatered cake to baggable powder; ginger and spice processors drying milled pomace after juice pressing; vegetable-protein and flour producers drying milled intermediate without gelatinising it; dehydration plants finishing pre-dried granules to a powder cut; any wet granular feed that cake-dryers would cake and belt-dryers would sour — including spent tea leaves, fruit-peel powder and pectin intermediates.

Not suitable for

Whole or sliced product — a flash duct carries particles, not shapes; use belt, tray or freeze drying for intact geometry. Sticky or sugar-rich feeds that clump instantly on contact will blind the feeder and agglomerate in the duct without back-mixing dry product. Very fine, dust-explosive powders need explosion-venting design and should be quoted as such, not standard. And low-volume producers under fifty kilos a day belong on a tray dryer with a fan, not a duct system.

Material & compliance

Duct, cyclone, feeder and product-contact parts in SUS304 (EN 1.4301); air heater and exchanger food-compatible; cyclone and duct seams ground and crevice-free so powder cannot lodge and discolour. Dust-hazard design — venting, earthing, no internal ledges — matters as much as food finish on starchy powders.

Supplied with CE declaration of conformity and DoC on request; material certificate EN 10204 3.1 available for contact parts.

Selection notes

Ask for a drying test on your actual wet cake — inlet moisture and cake hardness dominate feasibility, and factories love quoting on dry-looking samples. Ask what exhaust-temperature control strategy holds exit moisture, because feed swings are real. Check cyclone separation efficiency and whether a bag filter follows, since powder loss is product and dust. Confirm heater options against your utilities — steam if you have a boiler, gas if you have supply, electric only for small units. Ask for particle-temperature evidence on heat-sensitive product; a flash dryer that runs hot is a gelatiniser in disguise.

When you should not buy this machine: If your product dries acceptably on the belt dryer you already run, adding a flash stage is a second fuel bill for a marginal gain. And if your feed is a wet slurry rather than a dewatered cake, evaporating that water in a duct is burning money — press or centrifuge first, then flash.

Key specifications

Parameter Value
Evaporation capacity 200-1500 kg/h water by model (TYPICAL, confirm with factory)
Inlet air temperature 130-180 °C (TYPICAL)
Residence time 2-10 s (TYPICAL)
Feed form Dewatered cake / wet granules, screw-fed
Exit moisture ≤8-12% controlled via exhaust temp (TYPICAL)
Heating source Steam / gas / electric exchanger
Contact material SUS304 (EN 1.4301)
Power supply 380V/3P/50Hz, 15-60 kW class

Specification values are industry-typical ranges for this machine class and are not verified against a specific factory datasheet. Replace them with measured factory data before publication.

FAQ

Why flash dry instead of using a belt dryer?

Speed and temperature exposure. A flash dryer touches the particle for seconds near wet-bulb temperature, so starch does not gelatinise and protein does not denature; a belt dryer holds product hot for 30-120 minutes, which is fine for slices and ruinous for fine wet powders. Match the dryer to the physics of your feed.

How wet can the feed cake be?

Practically up to 40-60% moisture if the cake crumbles and feeds; beyond that, back-mixing with dry product or further dewatering is required. This single question — what is your real cake moisture — decides more quotations than any datasheet number.

Is the powder uniform after drying?

Within the mix the duct produces; cyclone catch is consistent if feed is consistent. For a controlled top cut, add the sifter-and-recycle loop the manufacturer offers — most complaints about flash-dryer uniformity trace to skipping that option.

Related equipment

This unit is one stage of a complete processing line. For the full range of drying and dehydration equipment, or to compare this model against the Belt Hot Air Dryer 1 t/h 30 kW, see the complete equipment catalogue. Capacity, material grade and utility requirements can be confirmed through a quote request.

material

SUS304 (EN 1.4301)

power

380V/3P/50Hz, Customizable

certification

CE+DoC (EU 2023/1230 ready)

surface_finish

Ra≤0.8 μm (food-grade)

application

Starch, Ginger Pomace, Protein Flour

capacity

200–1500 kg/h

automation

Fully Automatic

heating_source

Steam / Gas Hot Air

Reviews

There are no reviews yet.

Be the first to review “Flash Dryer 500 kg/h”

Your email address will not be published. Required fields are marked *