Fluidized Bed Dryer 800 kg/h

Fluidised bed dryer that suspends small cut pieces in an upward air stream, drying them fast and evenly with every surface exposed.

SKU: VL-046 Category: Tag:

Fluidized Bed Dryer

Fluidized bed dryer suspending cut pieces in a stream of heated air

Fluidised bed dryer that holds small pieces of product in suspension on a rising column of heated air, so that drying happens on every surface at once.

How it works

Heated air is blown upward through a perforated distributor plate at a velocity high enough to lift the pieces without carrying them away. The bed behaves like a boiling liquid: pieces move continuously, all surfaces are exposed to the air, and heat and mass transfer are far faster than in a static bed. Air velocity sits in a window — below minimum fluidisation the bed just sits there, above entrainment the product is blown out of the chamber. Dried product discharges over a weir or through an outlet at the bed level.

The window is narrow and depends on piece size and density, which is why a fluidised bed suits small, uniform pieces and struggles with a mixed load.

Suitable for

Diced and sliced vegetables; peas, beans and sweetcorn; small pieces going into IQF lines as a pre-dry; herbs and leaf where fast drying preserves colour; uniform small product where drying speed and uniformity both matter.

Not suitable for

Large or whole pieces that cannot be fluidised at a practical air velocity; product with a wide size range, where small pieces are blown out before large ones are dry; sticky or sugary product that agglomerates in the bed; very fragile product damaged by the constant motion.

Material & compliance

Distributor plate, chamber and ducting in SUS304 (EN 1.4301); air heated indirectly or filtered to food-contact standard. Chamber designed for access and washdown; air distribution and filtration accessible for cleaning.

Supplied with CE declaration of conformity and DoC on request; material certificate EN 10204 3.1 available for contact parts.

Selection notes

Test on your own product at your own moisture: fluidisation is specific to piece size and density, and a machine that works beautifully on diced carrot may simply blow peas out of the chamber. Ask what the air velocity window is for your product and how it is controlled. Check fines handling, because a fluidised bed generates fines and they either go to a cyclone or go up the stack.

When you should not buy this machine: If your pieces are large, uneven or fragile, a belt dryer will handle them with far less fuss. Also skip it if the product is sticky: agglomeration in a fluidised bed is difficult to control and will leave you with lumps rather than free-flowing dried product.

Key specifications

Parameter Value
Capacity 100-5000 kg/h by bed area (TYPICAL, confirm with factory)
Inlet air temperature 60-140 °C by product (TYPICAL)
Air velocity Set above minimum fluidisation for the piece (TYPICAL)
Residence time 5-30 min by product and moisture (TYPICAL)
Heating source Steam, gas or electric (TYPICAL)
Contact material SUS304 (EN 1.4301)
Power supply 380V/3P/50Hz or 415V/3P/50Hz, customizable

Specification values are industry-typical ranges for this machine class and are not verified against a specific factory datasheet. Replace them with measured factory data before publication.

FAQ

Why is my product blown out of the bed?

Air velocity above the entrainment velocity for your smallest pieces. Either reduce the air or remove the fines before the dryer, and check whether the product size range is too wide for one bed.

Can it dry whole vegetables?

Usually not well. Whole pieces need high air velocity to fluidise, which brings them close to being carried out. Belt or cabinet dryers suit whole product better.

How even is the drying?

Very even, because pieces are constantly moving and every surface sees air. That uniformity is the main advantage over a static bed, and it shows up as consistent final moisture rather than wet cores in larger pieces.

Related equipment

This unit is one stage of a complete processing line. For the full range of drying and dehydration equipment, or to compare this model against the Belt Hot Air Dryer 1 t/h 30 kW, see the complete equipment catalogue. Capacity, material grade and utility requirements can be confirmed through a quote request.

material

SUS304 (EN 1.4301)

power

380V/3P/50Hz, Customizable

certification

CE+DoC (EU 2023/1230 ready)

surface_finish

Ra≤0.8 μm (food-grade)

application

Root Vegetables, General Produce, Leafy Greens

capacity

0.5–1 t/h

automation

Fully Automatic

heating_source

Steam, Gas (LPG/Natural), Electric

Reviews

There are no reviews yet.

Be the first to review “Fluidized Bed Dryer 800 kg/h”

Your email address will not be published. Required fields are marked *