Drum Dryer 400 kg/h feed

Rotating heated drum that dries fruit and vegetable puree into flakes or powder in a single pass, for soup mixes, baby food and ingredient production.

SKU: VL-057 Category: Tag:

Drum Dryer

Drum dryer turning fruit and vegetable puree into flakes or powder

Drum dryer that spreads a thin film of puree or slurry onto a rotating heated drum, drying it in less than one revolution and discharging it as flakes or powder.

How it works

A hollow drum is heated internally, usually by steam. Product is fed into the nip between the drum and an applicator roll, or into a pan beneath the drum, so that a thin film is picked up on the drum surface. As the drum rotates, the film dries against the hot surface; before the revolution completes, a doctor blade scrapes the dry film off as flakes. Thickness is set by the applicator gap, and drying is set by drum speed and surface temperature.

Drying takes seconds, so throughput is set by surface area rather than by residence time, and the product sees a short, intense heat exposure.

Suitable for

Fruit and vegetable purees destined for flake or powder; tomato powder and vegetable flakes for soup and sauce bases; baby food and instant mixes; potato flake production; product that will be reconstituted, where flavour and colour retention matter more than particle structure.

Not suitable for

Product that must keep a piece structure, which needs a belt, cabinet or freeze dryer; very high-sugar feeds that stick to the drum and will not release; heat-sensitive product where even short high-temperature exposure degrades colour or flavour; low-volume production where a spray dryer or tray dryer is cheaper.

Material & compliance

Drum, applicator roll, doctor blade housing and feed pan in SUS304 (EN 1.4301); drum surface finished to the required specification and documented. Steam system and condensate removal designed for the duty; guards interlocked over the nip and the doctor blade.

Supplied with CE declaration of conformity and DoC on request; material certificate EN 10204 3.1 available for contact parts. Pressure parts carry the documentation required for the operating envelope.

Selection notes

Ask for a trial on your own puree at your own solids — drum drying is sensitive to solids content, and a feed that is too dilute will cost you capacity rather than quality. Check how the film is applied and how the blade is adjusted, because those two set your flake quality. Confirm how the drum surface is cleaned and what the finish is, since release and product build-up depend on it.

When you should not buy this machine: If you are drying a high-sugar fruit puree without carrier or formulation change, expect sticking and difficult release — a spray dryer with carrier, or a freeze dryer, will serve better. Also skip it if you need whole-piece dried product: a drum dryer destroys structure by design.

Key specifications

Parameter Value
Feed rate 50-2000 kg/h feed by drum size (TYPICAL, confirm with factory)
Drum surface temperature 120-160 °C by product (TYPICAL)
Drum speed 1-10 rpm adjustable (TYPICAL)
Film thickness Set by applicator roll gap (TYPICAL)
Heating source Steam inside the drum (TYPICAL)
Contact material SUS304 (EN 1.4301)
Power supply 380V/3P/50Hz or 415V/3P/50Hz, customizable

Specification values are industry-typical ranges for this machine class and are not verified against a specific factory datasheet. Replace them with measured factory data before publication.

FAQ

Drum dryer or spray dryer — which for vegetable powder?

A drum dryer is cheaper, simpler and produces flakes rather than fine powder; a spray dryer produces a soluble powder and suits heat-sensitive liquid better. Choose on the product form you need to sell.

Why does product build up on the drum?

Film too thick, drum speed too high, or solids too low for the temperature set. Adjust thickness and speed before raising the temperature, which risks scorching.

What form does the dried product come out in?

Flakes or coarse powder, depending on the blade and the drum settings. If you need a fine, free-flowing powder, plan a milling step after the dryer.

Related equipment

This unit is one stage of a complete processing line. For the full range of drying and dehydration equipment, or to compare this model against the Spray Dryer 500 kg/h feed, see the complete equipment catalogue. Capacity, material grade and utility requirements can be confirmed through a quote request.

material

SUS304 (EN 1.4301)

power

380V/3P/50Hz, Customizable

certification

CE+DoC (EU 2023/1230 ready)

surface_finish

Ra≤0.8 μm (food-grade)

application

Tomato, Apple/Pear, Root Vegetables

capacity

0.5–1 t/h

automation

Fully Automatic

heating_source

Steam

Reviews

There are no reviews yet.

Be the first to review “Drum Dryer 400 kg/h feed”

Your email address will not be published. Required fields are marked *